AQL Sampling Plans: How to Use the Table for Electronics Inspection

AQL sampling is the industry-standard method for deciding whether to accept or reject a production lot based on inspecting a statistical sample. Every buyer sourcing electronics from China needs to understand how to use the AQL table — it determines how many units to inspect, how many defects are tolerable, and what happens when the lot fails. AQL is the operational backbone of any professional pre-shipment inspection engagement.

Overview

AQL (Acceptable Quality Level) is defined in ANSI/ASQ Z1.4 (attribute sampling, used for pass/fail decisions on electronics) and ANSI/ASQ Z1.9 (variables sampling, used for measurable characteristics). The AQL value does not mean “every lot will have this defect rate.” It means “in the long run, lots submitted at this defect rate will be accepted about 95% of the time.” It’s a long-run process quality index, not a per-batch guarantee.

The standard distinguishes defect severity: Critical (safety hazard, regulatory non-compliance), Major (likely to fail or cause customer return), and Minor (workmanship imperfection, unlikely to affect function). You apply different AQL levels to each class — and you must define which defects fall into which class before inspection begins, in writing, in the inspection agreement.

Key Parameters

AQL Level	Defect Class	Typical Application
0	Critical	Zero tolerance — any critical defect = reject lot
0.065	Critical	Very tight — used for medical, safety-critical
0.65	Critical	Standard for critical defects in electronics
1.0	Major	Standard major defect AQL for CE/FCC markets
2.5	Minor	Standard minor/cosmetic defect AQL
4.0	Minor	Acceptable for less visible cosmetic items

Inspection Level	Sample Size	Use Case
General I (G-I)	Smaller sample	Low-risk, established supplier, stable process
General II (G-II)	Standard	Default for most pre-shipment inspections
General III (G-III)	Larger sample	New supplier, first production run, high-risk
Special S-1 to S-4	Very small	Destructive testing, expensive testing per unit

How to Use the AQL Table — Step by Step

Step 1: Determine lot size. This is the total number of units in the production run being inspected — not the total order size if it spans multiple runs.

Step 2: Select inspection level. Default is General Level II (G-II) for most pre-shipment electronics inspections.

Step 3: Find the sample size code letter. Use the lot size + inspection level to look up the code letter in Table 1 of ANSI/ASQ Z1.4.

Common code letters for G-II:

Lot Size	Code Letter	Sample Size (G-II)
2–8	A	2
9–15	B	3
16–25	C	5
26–50	D	8
51–90	E	13
91–150	F	20
151–280	G	32
281–500	H	50
501–1,200	J	80
1,201–3,200	K	125
3,201–10,000	L	200
10,001–35,000	M	315
35,001–150,000	N	500

Step 4: Find accept/reject numbers. Look up the code letter in Table 2 (single sampling, normal inspection) at your chosen AQL level.

Example: 5,000 unit lot, G-II, AQL 1.0 for major defects.

Lot 5,000 → Code J → Sample size: 80 units
At AQL 1.0: Accept if ≤ 2 defects, Reject if ≥ 3
This means: inspect 80 randomly selected units. If you find 2 or fewer major defects, accept the lot. If you find 3 or more, reject it.

Example 2: 5,000 unit lot, G-II, AQL 2.5 for minor defects.

Same Code J, 80 units
At AQL 2.5: Accept if ≤ 5, Reject if ≥ 6

Tightened and Reduced Inspection

ANSI/ASQ Z1.4 includes switching rules. If a supplier fails 2 of 5 consecutive lots on normal inspection, switch to tightened inspection (smaller accept numbers — more sensitive). After 5 consecutive lots pass tightened inspection, switch back to normal. After 10 consecutive lots pass normal inspection, switch to reduced inspection (smaller sample size). These switching rules reward consistently good suppliers and quickly catch deteriorating processes — use them if you have ongoing volume with a single factory.

Defect Classification — Define This in Writing

Before the inspection, you and your inspector (or third-party QC firm) must agree on a defect list. Example classifications:

Critical defects (AQL 0 or 0.65):

Exposed live conductors accessible to end user
Missing regulatory marking (CE, FCC ID) on product
Battery polarity reversal possible without user intervention
Any safety function disabled

Major defects (AQL 1.0):

Unit powers on but primary function fails
Charging does not work
Button/switch mechanically broken
Incorrect language on UI or label

Minor defects (AQL 2.5–4.0):

Cosmetic scratches not visible in normal use
Minor paint drips on non-visible surface
Slight variation in LED brightness (within spec)
Minor flash on plastic (not sharp)

What Happens After a Rejection

When the inspector’s sample fails at any defect class, you have three options:

100% sort: Factory manually inspects every unit, removes/repairs defective ones, then resubmit for re-inspection. Cost is borne by factory. Expect 5–10 days delay.
Rework and re-inspection: Factory fixes the defective units (e.g., re-labels, re-tests). Re-inspection is typically at tightened level.
Reject the lot: Refuse shipment. Factory must produce a new lot or repair and fully re-inspect.

Always document the rejection in writing with the inspection report attached. Do not verbally agree to accept a failed lot “because it’s mostly okay” — this weakens your position for future lots.

What to Specify When Ordering from China

Inspection reference standard: ANSI/ASQ Z1.4, Single Sampling, Normal Inspection
Inspection level: General Level II (state this explicitly — inspectors default to this, but some use G-I which gives smaller samples)
AQL by defect class: e.g., “Critical: 0.65, Major: 1.0, Minor: 2.5”
Defect classification list: attached as an appendix to the PO or quality agreement — never leave this verbal
Sampling must be random: inspector selects units from across the production run, not from boxes the factory presents

Quality Checks

The biggest process control failure is non-random sampling. If a factory pre-stages “good” units for inspection, the statistical assumptions of AQL sampling are violated and the accepted lot may not reflect the true lot quality. A professional third-party inspector (SGS, Intertek, QIMA, or equivalent) will break carton seals from multiple pallet positions and select randomly. When hiring a third-party inspection service, verify that their inspection report documents the carton numbers and positions from which samples were drawn.

Cost for a single pre-shipment general inspection (AQL per Z1.4): $200–400 for a standard electronics lot, including report same day. Third-party inspection is almost always cheaper than the rework cost from accepting a bad lot. For PCB assembly runs, combining AQL sampling with a factory audit on new suppliers provides the strongest risk coverage.

Common Issues

Inspector selects convenience sample: Units from the top of the nearest pallet. Biased toward units the factory may have placed there. Solution: require carton selection from random positions and document box numbers in the report.

AQL level applied inconsistently: Factory claims “we passed AQL inspection” but used AQL 4.0 for everything including critical defects. Always specify the AQL level by defect class in the purchase agreement, not just “AQL inspection.”

Lot failure ignored: Buyer accepts the lot anyway under time pressure and factory promises rework. Defective units still ship. Solution: do not accept the shipment until a re-inspection report shows pass. Factor lead time contingency into your schedule for this scenario.

IPC-A-610 Acceptance Criteria — defines what constitutes a defect on PCBAs
SMT Assembly Process — process context for PCBA defects
X-Ray Inspection — destructive/semi-destructive inspection for hidden joints
Factory Audit Checklist
How to Source Electronics from China
Quality Inspection Services
Factory Audit & Verification
PCB Manufacturing & SMT Sourcing